Why Electric Water Heater Won’t Heat

An electric water heater is supposed to deliver hot water to your faucets and showers. The moment it fails to do this, then you know that there is definitely something wrong. There are a number of things that you can look into to find out why electric water heater won’t heat.

But before you do anything, make sure that the power feeding the water heating unit is completely turned off. Also make sure that you are not standing in a pool of water because electricity and water are a deadly mix. So, let’s take a look why you aren’t getting any hot water.

Possible Reasons

Good news for you is that there are only a handful of possible reasons why your water heater is not turning out hot water like it should. Here are some reasons to consider.

Electricity – since we are talking about electric water heaters, the first reasonable thing to look at when it is not functioning properly is whether it is getting the right amount of power it needs to operate.

electric water heater

You can check the main switch as well as the circuit breaker where the water heater is connected to. A tripped circuit breaker only needs to be reset by flipping it all the way off before turning it back on again.

In case you are dealing with a blown fuse, you would need to replace that fuse. Make sure that you use one with the same rating. If the fuse repeatedly blows or the circuit breaker trips consistently, then it is time to call a licensed electrician to check it out.

Heating Element – another obvious reason why there is no hot water is a problem with the heating element. If either of the two heating elements fail to fire up, then you could end up with no hot water supply.

High Temperature Cutoff – check this from the water heater’s panel. Open it up and push the reset button. When you do not hear a clicking sound or there is still no power, there is a high probability that the temperature cutoff has gone bad. Have a licensed professional repair it at once.

Lack of Water – another reason why you are not getting hot water is that there may be too little or no water inside the compartment of your electric water heater. This condition can result in the malfunctioning of the thermostat. If you observe water leaking, this is an indication that the water heater needs replacement.

Other Things to Check

why electric water heater won’t heat

Aside from these, there are also some other things that you can check on to see why electric water heater won’t heat. One of the more commonly overlooked factors is the water heater timer. If you have one installed, you should consider the possibility that it might be turned off or is not working at all. Have your water heater timer tested to make sure that it is in good working order.

We discussed earlier the possibility of one or both heating elements failing. Another possibility that can be seriously considered when it comes to the heating element is that it can be coated with scales. When this happens, you can be assured that its ability to heat water will be greatly reduced.

Leaks is another possible cause why you are not getting enough hot water supply. The leak can be on the unit itself or on the supply lines leading to the unit.

There is a danger that must be stressed when it comes to leaks and electric water heaters. The water may find its way into the electrical wirings of the unit and cause a short circuit, or worse, a fire. So make sure that any electrical defects are corrected immediately for your own safety.

These are all the possible reasons why electric water heaters won’t heat water. If you’ve gone through all of these and still fail to get enough hot water, then it is time for you to call on professional help.

Tags : , ,

Things to Know about Drain Cleaning

A lot of home owners simply forget about drain cleaning. While some thinks that cleaning the drain is a lot of work. Regardless of the reason for not cleaning, you are getting your property in a lot of risk when drain line issues start to occur. It is necessary that you regularly clean your drain lines to make sure that it would function well for a long period of time and will not cause you an expensive damages and repair.

Slow Draining

When you experience slow draining, do not simply get used to it. This kind of draining is already a sign that clog is slowly building up in your drains. Since this condition is not that serious, you could deal with it using some homemade solutions.

One of the most popular is the combination of baking soda, vinegar and hot water. Simply pour half a cup of baking soda in the drain followed by half a cup of vinegar, then wait for a couple of minutes for the reaction to take care of the clog. The combination of these two could result to bubbling and fizzing that could break down minor clogs.

After a couple of minutes, rinse it with hot water. Try letting water flow the drain and if you still observe slow draining, repeat the step until the drain is clear.

Using Drain Cleaners

If using homemade solutions does not work, you could go for using popular drain cleaners you could find in the market. Just be sure that you choose one that does not use dangerous chemicals.

It is also good to invest in products which are more popular to a lot of homeowners. Even though these are often more expensive, at least you could be sure that it is safe to use and above all effective. There is no point in using cheap products that do not work.

Drain Cleaning tools

Some of the popular tools for drain cleaning are plunger and draining snake. If you have a draining snake at home, it is better to use this tool. Simply insert the snake inside the drain. When you feel that it reached a certain clog, twist it a couple of times then pull it off.

Using a draining snake could often deal with clogs or blockages that occurred near the fixture. However, when the problem is far down the drain, it is not that useful.

Going for professional Service

When you call the aid of the professional plumbers to do the drain cleaning they would first access the condition of your drain lines. If they see that the problem is already worst, the most effective method for cleaning the drain is hydro jetting.

If you need professional drain cleaning service, call Jonos Plumbing. Call us anytime for there will always be a professional plumber ready to deal with clog or blockage problem in your drain lines. We know that a clog could be a major inconvenience in your home so we make sure that we will be with you fast.

Tags :

Proper Water Heater Maintenance to Keep your Heater for Long

Today, an important part of your home is the water heater. The same as with other appliances, water heater maintenance is also very important and could help homeowners free themselves from frequent troubles. There are basic maintenance techniques that you could do personally to keep the unit in good condition.

Signs that the Heater Needs Cleaning

If you see that the water from the heater has some sediments or the color is not clear, these are signs that it needs cleaning. When the heater is not working efficiently, it is also a reminder that build-up of sediments is already serious.

A water heater that is not maintained properly could increase the consumption of energy in your home thus raising your energy bill. If you don’t want to waste money, better do water heater maintenance regularly.

Constantly check the anode rod on the tank for it keeps rust from occurring inside. If ever this is already used up, it needs replacement immediately. Failure to replace this could result to rusting inside the tank.

Common problems and their solutions

Build-up of Sediments

In time, sediments would slowly build-up at the bottom of the water tank due to the minerals present in the water. When this is not removed, it could start to accumulate in a level that is not anymore good for the heater.

You could do the cleaning by simply using a hose and a brush. Use a long handle brush to reach the bottom of the tank and simply brush off the sediments. After brushing you could flush this out on the drain valve.

Make sure that you attach first the garden hose on this valve before draining. The hose could lead to the drain or anywhere outdoor. Simply let water to continue filling the water tank while it is drained. In the beginning you will see that the water is dirty. When you observe that water coming out from the hose is already clear, it means that the tank is already clean.

Water Too Hot or Too Cold

If you are not satisfied with the hot water you get from the faucet, you simply need to adjust some setting on the thermostat.

Signs that your heater needs replacement

Knowing if a water heater needs replacement is quite easy. If you have been using your water heater for over 15 years already, it is best to think about its replacement. When you observe that it frequently experience problems lately, investing in a new heater is the best thing to do.

Latest water heaters are more reliable and energy efficient so definitely it would help you save money in time. Plus, these heaters would also last longer compare to the old ones especially when it is properly maintained.

We have been doing this job for many years. With this, you could be sure that our plumbers are well-experienced to maintain your heater at home and to do the necessary replacement when needed.

For your water heater maintenance or replacement needs, do not hesitate to call Jonos Plumbing.

Tags :

What is Hydro Jetting For Sewer Lines?

When your sewer lines experience problems such as major clog and backed up, you need an effective way to deal with it like hydro-jetting. Such issues should not be left unattended for a long time since it could result to expensive damages.

What is Hydro Jetting?

Hydro-jetting is a process that is aimed at cleaning your sewer lines thoroughly. The cleaning is done by using extremely high pressure of water to break anything that blocks the sewer lines.

It forces everything out of your sewer lines including minor clogs. This is why a lot of homeowners consider this service since their lines are cleaned thoroughly.

With regular drain cleaning through hydro-jetting, your drain lines would surely look like new in the inside. The pressure of the water is so strong that it could even deal with tree root problem.

The good thing with this service is you don’t have to dig any part of your property to eliminate major clogs. The highly pressurized water could reach farther areas in your sewer lines and still being able to remove most of the clogs in it.

Since it only uses water, you are not causing any damage in your pipes unlike using some products with strong chemical content. Often times, a professional plumber would perform a thorough video inspection on the sewer lines after the cleaning process is done. This is to ensure that there is no more clogs and wastes from your home could now flow freely.

Other Benefits of Hydro-jetting

The good thing about the thorough cleaning and video inspection is that any leaks and cracks in your pipes could be easily spotted. With this, your plumber could give you some options on how to deal with it.

You could now effectively deal with any problems in your drains and keep major issues at bay. It is very helpful so that you won’t have to face the expensive repairs on some major problems due to sewer line issues.

How to Find the Right Plumber

Today, almost all plumbing companies offer this service. However, they are not the same when it comes to the level of their expertise. With this, you have to ensure that you find the right company to hire.

What is important is checking the license of the plumbers. Most licensed plumbers are trained well and have enough experience when it comes to doing various plumbing services which include hydro-jetting.

You could try to go online and search for reliable plumbing companies in your place. Read tons of testimonials and reviews about their service so that you know a lot about them prior to hiring.

Hydro-jetting has to be done by professionals only so that you get good results. Jonos Plumbing could help. We have been offering this service for many years already. We use the latest machines and tools in doing the job and our plumbers are trained well to use such equipment to the fullest. We guarantee customer satisfaction in all the services we offer.

Call 714-257-5697 

Tags :

Options for Water Pressure Restoration

Restoration of water pressure can be done by using trenchless leak detection and repair services from professional plumbing contractors.

Advantages of Trenchless Solutions

Trenchless leak detection and repair is considered as one of the newer and more innovative approaches to ensuring the integrity of plumbing pipes.  It is considered as an effective way of maintaining water pressure and preserving water supply to the entire household plumbing system.

There are certain advantages why this type of solution is widely preferred by many professional plumbing contractors.

  • Fairly accurate in pinpointing the exact location of leaks to minimize damages
  • Provides multiple repair options that can lower the cost of permanent repairs
  • Non-metallic alternatives can be used to repair damaged pipes to prevent future corrosion

Trenchless Solution Procedure

Normally one of the most difficult sources of leak to detect is those located behind structures or from underground pipes.  This is why professional plumbing contractors use electronic leak detection equipment to find the source of leaks.  These are extremely accurate in pinpointing the source of leaks.

Once the actual source of the leak has been found, repair options will be considered.  Considerations will use a number of factors like lower costs, less intrusive approach, and requires minimal time to implement.

Normally, some of the repair options that are considered are:

  • Rerouting or spot repairs
  • Epoxy pipe rehabilitation
  • Copper or PEX re-piping

These most common choices have the highest cost benefits that can conveniently fit into the budget of average homeowners.

Carrying Out the Solution

After the repair options have been discussed with homeowners, it is necessary to choose which one would be considered as most beneficial.  Homeowners would generally rely on the findings and recommendations of professional plumbing contractors.

The water supply to the home would normally be cut off temporarily to ensure that further damage will be avoided.  The chosen solution would then be implemented and normally completed within the day depending on the time that it was started.

Once the repairs have been finished, testing of the entire system will be done.  The water supply will be completely turned on by this time.  Water pressure should normalize by this time.  It may be necessary to allow air packets out of the system by allowing water to run continuously for a few minutes.

Understanding Trenchless Solutions

Basically, when trenchless plumbing solutions are offered, this means that there is no need to keep on digging throughout the entire plumbing system to make sure that leaks are properly plugged up.

Homeowners may not readily recognize the need for trenchless repair solutions, but when you consider that plumbing pipes are the primary method of delivering and preserving water pressure to the entire household, then the integrity of plumbing pipes become extremely important.

Call Jono’s Plumbing today for professional services that is truly reliable, fast and friendly!

The Decision to Re-pipe

The decision to undergo re-piping with copper pipes should be done based on its benefits and upon consultation with re-piping specialists.

Going with Copper Re-piping

It must be made clear that there are other alternatives to copper re-piping.  The choice of copper therefore should be done based on the unique benefits that it can inject into your plumbing system and your home.  Some of the reasons why many homeowners choose copper re-piping over other re-piping technologies include:

  • Elevated water pressure
  • Cleaner and better tasting water
  • Resistant to rust and corrosion
  • Ideal for all weather conditions
  • Impervious to fire
  • Extremely durable
  • Can last a lifetime
  • Relatively easy to install
  • Increases the value of your property

 

Preparation for Copper Re-piping

The reality is that there is very little that should be done to prepare your home for copper re-piping.  If there should be some amount of preparation, these are limited mostly to the following:

  • Cleanout underneath bathroom and kitchen sinks
  • Clear access to water heater
  • Attic (if any) must be accessible

 

It is not necessary to do any of these preparations since they are part of the services that we offer.  We will do a walkthrough with you before and after completion of the re-piping process to ensure that you become familiar with key features of your new plumbing system like the location of shutoff valves.

Choosing Re-piping Specialists

Normally, homeowners are not aware that re-piping should be carried out by specialists and not just any plumbing contractor.  This is essential to make sure that the entire re-piping procedure is handled correctly and properly.

Choosing re-piping specialists instead of settling for just any professional plumbing contractor can bring you the following advantages:

  • They are licensed and bonded to handle copper re-piping solutions
  • Provide better choices of materials to use
  • Properly trained and knowledgeable in the latest techniques and technology
  • Can deliver high quality work at comparatively lower prices
  • Fast and efficient completion of re-piping jobs in as short as a day
  • Come with specialized contractors to handle the patching of walls
  • Ensure the protection of your floors and carpets until project completion

 

All of these become critical factors in ensuring that you get the right re-piping specialists to handle the job.  Another thing worth mentioning is that copper re-piping specialists are in the best position to answer all your questions on how the entire process will go through and make sure that there will be no surprise fees along the way.

We at Jono’s Plumbing are experts when it comes to re-piping. Call us today for questions, quotes or immediate service!

The Basics of Water Softeners

The professional installation and repair of water softeners like what Jono’s Plumbing offers will ensure the health of your plumbing pipes, fixtures, and appliances.

Function of Water Softeners

The main body of the water softener tank is filled up with resin beads that are covered with sodium ions.  When hard water passes the resin beads, they act like magnets and attract the magnesium and calcium ions and replace them with sodium ions.  This strips the water of its hardness which accumulates and saturates the beads.

Recharging of the beads uses a process known as regeneration.  The control valve at the top of the tank is responsible for this process and functions as the brain of the water softener system.  Strong brine solution is used to flush the resin tank and cover it with sodium ions to replace the accumulated hardness, allowing the beads to be used again.

Disadvantages of Hard Water

It is important to be aware of the drawbacks of hard water to understand the value of water softeners and why they should be maintained.  Some of the most common disadvantages include:

  • Contributes to costly and inefficient use of water appliances
  • Scale deposits can form on plumbing fixtures and appliances causing failure
  • Clog pipes with scales  that reduces water flow resulting in pipe replacement
  • Increase energy bills by as much as 25%
  • Cause spotting and filming on shower doors and tableware
  • Increased spotting can occur when hard water is subjected to heat
  • Clothes feel scratchy and harsh
  • Damages clothes and shortens its life by 40% at the most
  • Soap curd is left on skin which causes irritation and bacteria growth

Proper Water Softener Maintenance

To ensure that you continue to enjoy the benefits of your water softener, it is important that it is properly maintained for efficiency.  There are a few things to pay attention to:

  • Cleaning of the brine tank – this is to ensure that no salt has formed on the crust or dome inside the brine tank.  The salt dome is normally caused by adding too much salt or frequent adding of salt.  You should breakup the salt using a broomstick and wash the tank thoroughly with soap and water.
  • Cleaning iron-fouled resin bed – the iron in the water will eventually cloud the resin bed responsible for the removal of hard water particles and replacing them with sodium.  In order to refresh the bed, you should purge the waste water and regeneration the resin bed.  The regeneration knob in the control valve should be set to service.
  • Cleaning resin tank injector – sediment from dirty salt can plug the injector.  You have to engage the bypass valve before you can clean it so that the water supply will be cut.  The water pressure should be relieved by manual regeneration.  The caps should be removed and the injector cleaned completely.

If you need any assistance, don’t hesitate to contact Jono’s Plumbing.

Call us at 714-257-5697 

How to Unclog a Drain

One of the most annoying problems experienced by homeowners today is clogged drain. When this problem is not addressed fast and properly, it could cause flooding on your floor. Your tub, sink and toilet might not be working effectively as well. There is an effective way on how to deal with this problem. Remembering these simple tips could greatly help.

Flush with Boiling Water

The first thing that you have to do is to boil water and let it run through your drain. Though this is not a guarantee to unclog your drains, it is very effective when it comes to dealing with slow drain. There are times that the clog is not that serious or it’s just a light clog. This usually leads to slow drain. Boiling water could easily clear out this small blockage with less effort on your part. The heat of the boiling water could break-down slight blockage in your drain. After pouring hot water on your drain, wait until the sink or tub is drained then let water flow.

Important note: When using boiling water, check first if your pipes are made of metal. If ever you have PVC pipes, boiling water could soften the pipes or melt the joints in the pipes. For PVC pipes, it is better to only use hot water just as hot as what your top makes.

Make Your Own Drain Cleaner

Most drain cleaners you could purchase in the market could only work on certain kind of clogs. However, most professional plumbers do not recommend that you use those drain cleaners in the market for they usually include strong chemicals in their product that could cause problems on your drain. Using cleaners with strong chemicals should be your last resort. It is best to make your own like using baking soda and vinegar.

Some drain cleaners are only effective on certain kinds of clogs. You could run out and buy a bottle of commercial drain cleaner, but even many plumbers will tell you that it should be a last resort. If you know your clog is because of grease, try making your own drain cleaner from vinegar and baking soda.

Making your own drain cleaner is not that hard to do. Pour a half-cup of baking soda directly on the drain. Then add a half of vinegar. This will create a reaction which results to bubble and fizz. In order for the fizzing to be more effective, close the drain or find something to cover it. Let this mixture site in the drain for about half an hour or longer if you have the time. After this, flush the drain with hot water.

Plunge It

There are a lot of people who do not want to use a plunger in dealing with clogged drain. However, when the problem arises, you need to know how to use a plunger effectively. For better results, it is best to use cup plunger in plunging your sink or bathtub drain. You could also place a duct tape on top of the sink or tub. This will force the air to go down the drain and into the clog. With this, the clog could break down easily. If the plunger did not work, try to use a drain snake. This also works best when a plunger does not work.

Following the tips mentioned above could really help. If all of these fail, now is the right time to call the experts to handle the problem. There are just some plumbing issues that you could not deal on your own. For a faster and better solution to your problem, better have the experts to do it like Jono’s Plumbing. Their knowledge and experience in plumbing makes them a dependable company for most homeowners.